1. The work table is in the use of an electromagnetic sucking device or disc cliker; the vertical pillar and the machine tool bed are connected by the three-point position regulation system, which helps to process the work piece into inside cave shape or crown shape; the spindle is able to rotate ±45° around the horizontal axis. The grinding wheel spindle is driven by a loaded electric motor; the grinding wheel is in the use of either cup/dish shaped or even distributed trapezoid carborundum brick wheels around the circumference.
工作台可采用电磁吸盘或花盘；立柱与床身采用三点调整机构联结，便于将工件平面磨成中凹或中凸形状；磨头可绕水平轴旋转±45°；磨头主轴采用装入式电机驱动；砂轮可采用杯、碟形式或多块砂瓦圆周均布组合式结构。
2. The work table is in the use of an elec- tromagnetic sucking device or Disc clicker; the vertical pillar and the machine tool bed are connected by the three-point position regu- lation system, which helps to process the work piece into inside ca- ve shape or crown shape; the spindle is able to rotate ±45° around the horizontal axis. The grinding wheel spindle is driven by a load- ed electric motor; the grinding wheel is in the use of either cup/d- ish shaped or even distributed trapezoid carborundum brick wheels a- round the circumference.
工作 台可采用电磁吸盘或花盘；立柱与床身采用三点调整机构联结，便于将工件平面磨成中凹或中凸形状；磨头可绕水平轴旋转±45°；磨头主轴采用装入式电机驱动；砂轮可采用杯、碟形式或多块砂瓦圆周均布组合式结构。
3. Among them the electromagnetic sucking disc has already become the domestic largest production base.
其中电磁吸盘已成为国内最大生产基地。
4. A sucking-in reception disc whose lower end is fixedly connected with the upper end of a material sucking pipe is fixedly arranged on the inlet end face of the blower fan by using a clip;
吸入接盘固装在风机入口端面上，其下端利用卡箍与吸料管上端固接，吸料盘固配在吸料管下端上；
5. Very small (to 3 inches) flattened marine fish with a sucking disc on the abdomen for clinging to rocks etc..
非常小的（3英寸）扁平海鱼，腹部下面有吸盘能将自己固定于岩石上。
6. Magnetometric sucking disc or working plateform is required for special work.
特殊工作另配磁力吸盘或工作平台。
7. Designing calculation of the versatile vacuum cup lifter Research on Adaptive Multi-Sucking Disc
多用真空吸具设计自适应式多真空室吸盘的研究
8. Sharing switch power device in hydraulic grab bucket and eletromagnetic sucking disc
液压抓具、电磁吸盘共用开关电源设备
9. The work table is in the use of an electr- omagnetic sucking device or disc clicker; the vertical pillar and the machine tool bed are connected by the three-point position reg- ulation system, which helps to process the work piece into inside cave shape or crown shape; the spindle is able to rotate ±45° ar- ound the horizontal axis. The grinding wheel spindle is driven by a loaded electric motor; the grinding wheel is in the use of either cup/dish shaped or even distributed trapezoid carborundum brick wh- eels around the circumference.
工作台可采用电磁吸盘或花盘；立柱与床身采用三点调整机构联结，便于将工件平面磨成中凹或中凸形状；磨头可绕水平轴旋转±45°；磨头主轴采用装入式电机驱动；砂轮可采用杯、碟形式或多块砂瓦圆周均布组合式结构。